KINEMATICS OF MACHINERY

Aryabhatta Knowledge University

KINEMATICS OF MACHINERY

  Sem. iv   2013                                    Time 3hr                        Full marks: 70

Attempt any five questions in which question no 1 is compulsory

1.       Choose the correct answer(any seven):

(a)    In a centrifugal method casting method

(i)                  Core is made of sand

(ii)                Core is made of ferrous metal

(iii)               Core may be made of any metal

(iv)              No core is used

(b)   The  binder in the case of synthetic sand ,is

(i)                  Water

(ii)                Clay

(iii)               Molasses

(iv)              Bentonite and water

(c)    Carburettors are manufactured by

(i)                  Fine sand casting

(ii)                Die casting

(iii)               Slush casting

(iv)              Shell moulding

(d)   In metals subjected to cold working condition ,strain hardening effect is due to____

(i)                  Slip

(ii)                Twinning

(iii)               dislocation

(iv)              fracture

(e)   A forging method for reducing the diameter of a bar and in the process making it longer

Is termed as

(i)                  Fullering

(ii)                Punching

(iii)               upsetting

(iv)              stamping

(f)     the brazing joint can be satisfactorily made on an article made of

(i)                  tin

(ii)                copper

(iii)               aluminium

(iv)              galvanized sheet

(g)    the electric resistance welding operates with

(i)      low current and high voltage

(ii)    low current low voltage

(iii)   high current low  voltage

(iv)  high current and high voltage

(h)   in MIG welding ,the metal is transformed in the form of

(i)      molecules

(ii)    fine spray of metal

(iii)   weld pool

(iv)  molten drops

(i)      injection moulding process is suitable for

(i)      thermosetting plastic

(ii)    thermoplastics

(iii)    both of the above

(iv)  None of the above

(j)     High speed gears are made from plastic of the type of

(i)                  Foalite

(ii)                Fibreglass

(iii)               Capron

(iv)              Polyethylene

2.       (a)   What are the advantages of casting process over other shaping process?

(b)   Write the uses of (i) gates ,(ii) riser ,(ii) core and (iv) chills

(c) On what factors , the selection of a suitable  core sand depends?

3.       What do you understand by ‘centrifugal casting’? describe the process of true centrifugal casting with the help of a neat diagram. What are its advantages and disadvantages?

4.       (a) What are crucible furnaces? where are they preferred and why?

(b) What are the major drawbacks of the casting process and how are they overcome?

5.       (a) What is a continuous rolling mill ?what are its advantages?

(b) What is hot extrusion? In how many ways it can be performed ? discuss their merits and demerits.

6.       (a) What is a coated electrode? Sketch the arc flame due to such an electrode and explain the different functions of the coating.

(b) Explain oxyacetylene welding.

7.       Describe any two of the following welding process with their advantages and disadvantages

(a)    TIG welding

(b)   Thermite welding

(c)    Electron beam welding

8.       (a) Describe the principal of powder metallurgy and how powder is produced.

(b)   Explain the process of sintering

9.       (a) How do thermosetting plastics differ from thermoplastics?

(b) Describe with neat sketch ,the plastic processing method of injection moulding. Also write its advantages and applications.

HYDRAULICS AND OPEN CHANNEL FLOW

Aryabhatta knowledge university

  Sem. iv   2013                               Time 3hr                            Full marks: 70

HYDRAULICS AND OPEN CHANNEL FLOW

Attempt any five question in which question no 1 is compulsory

1.       Answer any seven from the following in short in short ,preferably one or two sentences each:

(a)    What is hydraulics?

(b)   What is boundary layer thickness?

(c)    What type of flow is (i) breaking of dam, (ii) spreading of irrigation of water on a field?

(d)   What is specific energy?

(e)   What is critical depth?

(f)     What is Darcy-weisbach frication factor?

(g)    What is sequent depth ratio?

(h)   What is weak jump ?

(i)      What is backwater curve?

(j)     What is surge in unsteady flow?

2.        (a) define boundary layer and derive the expression for displacement thickness, and momentum

(b) a thin rectangular plate 2.25 m long and 12.5 m wide is towed through water ,having v=1.48*10^-6 m²/s, at 1.0 m/s velocity. Determine the total drag force on  both sides of the plate.

3.        (a) what do you mean by critical flow? Derive an expression for critical depth and Froude number for triangular channel.

 (b) A rectangular channel is 3.0 m wide and carries a discharge of 15.0 m³/s at a depth of 2.0 m. At a certain section of the channel, it is proposed to reduce the width to 2.0 m  and to alter the bed elevation by Δz to obtain critical flow at contracted section without altering the upstream depth. What should be the value of Δz?

4.       (a) explain the cause of channel in transition with a hump in a sub critical flow.

(b) A rectangular channel 3.6 m wide had a widely damaged surfaces and had a Manning’s n= 0.03. As a first phase of repair , what is the increase of discharge obtained as a result of repair?

5.       (a) sketch the possible GVF profiles in the serial arrangement of channels,if the flow is from left to right : (i) free intake –steep –sluice gate—mild slope,

(ii) mild—sluice gate –steep—horizontal—sudden drop.

(b) A channel has a multiple –roughness types in its perimeter .Assuming that the total discharge in the channel is equal to the sum of the discharges in the partial areas , show that the equivalent roughness is given by

                                      N=(PR^5/3)/₁ⁿΣ(P_iR_i^5/3/n_i)

6.       (a) Derive the equation for gradually varied flow and write the basic assumptions in analyzing the GVF.

(b) Water flows in 15 m wide rectangular channel at arate 115 m³ /s . bed Slope is 0.001 and n=0.125. A dam placed  downstream raises the height to 6.8 m  immediately behind the dam. What is the distance upstream to a point , where depth is 3.7 m? Find by two steps.

7.       (a) derive the equation for sequent –depth ratios and energy loss in exponential channels having A =K₁ y^a  in which k₁  and a are characteristic constants.

(b) A rectangular channel carrying a supercritical stream is to be provided with a hydraulic jump type of energy dissipation. If it is desired to have an energy loss of 5 m in the jump when the inlet Froude number is 8.5,determine the sequent depths.

8.       (a) define the celerity of a gravity wave and derive its equation for rectangular channel.

(b) A 2.5 m wide rectangular channel is carrying a flow depth of 2 m. Determine the height of a  surge  wave and its velocity if the discharge is suddenly increase to 10 m³/s at the upstream end.

9.       Write short notes on any four of the following :

(a)    Economical channel section

(b)   Sseparation of boundary laye

(c)    Specific energy curve

(d)   Factors affecting mannin’s n

(e)   Types of hydraulic jump

                                                                                                                                ^{techprojecthelper.blogspot.in}

ARYABHATTA KNOWLEDGE UNIVERSITY

NUMERICAL METHOD AND COMPUTATIONAL TECHNIQUE

  Sem. iv   2013                                    Time 3hr                        Full marks: 70

Attempt any five questions in which question no 1 is compulsory

1.       Answer any seven from the following:

                (a)            In C++ ,a mathematical expression 137% 10 yields

(i)                  13

(ii)                13.7

(iii)               0

(iv)              7

               (b)            Which of the following statements is true about the break statement?

(i)                  A break statement causes an exit only from the innermost loop

(ii)                A break statement causes an exit only from the innermost switch

(iii)               A break statement causes an exit only from all loops and switches

(iv)              A break statement causes an exit from the innermost loop or switches

                (c)            What is the process of converting one predefined type into another called?

(i)                  Type casting

(ii)                Expression

(iii)               Type promotion

(iv)              Type conversion

               (d)            The assignment statement a-=b; can also be written as

(i)                  a=b-1

(ii)                a=a-b

(iii)               a=a-(-b)

(iv)              a=b-a

               (e)            the operator which is used to access the address of a variable is

(i)                  &

(ii)                #

(iii)               @

(iv)              *

                 (f)            What do you mean by a difference equation?

                (g)            Define the order and degree of a difference equation with examples.

               (h)            What is the difference between an initial value problem and a boundary value problem ?

                  (i)            What do you mean by the order of convergence of an iterative method for finding the root of the equation f(x)=0 ?

                 (j)            When is the convergence of an iterative method for solving the equation f(x)=0 said to be (i) linear and (ii) quadratic?

2.       (a) find the root of the equation xtanx=1.28, that lies between 0 and 1, correct to two  places    of decimals, by bisection method

(b) Write a computer program using C/ C++ for the above equation using bisection method.

3.       (a) Find the Newton- raphson iterative formula for the reciprocal of a number N and hence find the value of 1/23, correct to 5 decimals.

(b) Write a computer program using C/C++ to find the smallest positive root /the largest negative root of the equation f(x)=0 , by using the simple iterative method.

4.       Solve the following system of equations by Jacobi’s iteration method and gauss-seidel’s method:

10x₁+2x₂ +x₃=3

X₁+ 10x₂- x₃=-22

-2X₁+3x2+10 x₃=22

5.       The population of a town Patna in the census is as given in the data. Estimate  the population in the year 1996 using Newton’s forward interpolation and backward interpolation formulae:

Year(x)	1961	1971	1981	1991	2001
Population (in 1000’s approx)	46	66	81	93	101

6.       (a) fit a curve of the form xy= a+bx² to the following data by the method of least square :

X	1	2	4	6	8
Y	5.43	6.28	10.32	14.86	19.51

 (b) Write a computer program using C/C++ to fit a straight line of the form xy=a bx² taking the above data, using the method of least square.

7.       The velocity of a particle at distance s from a point on its linear path is given in the following data :

S(m)	0	2.5	5.0	7.5	10.0	12.5	15.0	17.5	20.5
V(m/sec)	16	19	21	22	20	17	13	11	9

Estimate the time taken by the particle to traverse the distance of 20 meters , using Simpson’s one-third rule.

8.       (a) Find the value of y(1.1) ,using runge-kutta method of the fourth order , given that dy/dx=y² +xy ;y(1)=1

(b) Write a computer program using C/c++ to solve the above differential equation at specified pivotal points, using runge –kutta method of the fourth order.

9.       Solve the boundary value problem v’’(x)- xy(x)=0 for x_i=0, 1/3 ,2/3 , given that y(0)+y’(0)=1 and y(1)=1.